SINGLE READY PLASTER

Industrial product used for coating building surfaces (old plaster, brick, concrete, ceilings).

Replaces traditional plasters "roughcasted and marble."

Applied in the same way in two or three layers of 5-6 millimeters each.

The same material is used as a "scratch".

PRODUCED AS WHITE AND COLOURED

ADVANTAGES

Stable composition and mixture homogeneity

Very good workability

Strong adhesion without lime

No cracks or capillaries at high temperatures

Applied by hand or with a press

Has high resistance to frost (resistance to delamination - adhesion loss)

Manual

1. Clean dust from loose areas or oils formwork surface.

2. Dampen with water if it comes to absorbing surface or high temperature (over 30 degrees)

3. Combine material from the package to the appropriate amount of water to vessels or mixer until the slurry prepared obtain homogeneity and consistency.

4. Determine that a 25kilo sack of "GLORIA UNIPLAST" needs 5-6 liters of water. You have at your disposal 2-3 hours to use the quantity prepared before it starts to tighten and thicken. The time is calculated based on normal ambient temperature (23 ° C and 50% relative humidity)

5. Apply with a trowel until two players thick 5-6 millimeters

6. Smooth surfaces need a layer of "lath" from the same material

7. If it is applied to a greater thickness than the recommended, the product does not "sag" or getting detached from the background and is easily aligned afterwards.

8. When you start tightening surface to 'draw', smooth with float, hard sponge or styrofoam, after you put some water on them.

9. Each screed drying time ranges from one half to two hours, depending on temperature, relative humidity, wind, the absorbency of the substrate and the coating thickness.

10. In column associations or spar with bricks or other dissimilar surfaces use a reinforcing mesh plaster.

Consumption

They take 10 to 12 kgs of material to coat a square meter of 5-6 mm thickness.

RREADY PLASTER FINAL LAYER

WATERPROOF SILICONE MORTAR

Applied in the same manner in one or two layers of 3-4 millimeters.

PRODUCED AS WHITE AND COLOURED

ADVANTAGES

· Fixed composition and mixture homogeneity

· Very good workability

· Strong adhesion without lime

· No cracks or capillaries at high temperatures

· Apply with hand or press

· It has high resistance to frost, is water repellent material

Manual

1. Clean the surface of dust or loose areas and oils

2. Dampen with water if it comes to absorbing surface or high temperature (over 30 degrees)

3. Combine material from the package to the appropriate amount of water to vessels or mixer until the slurry prepared obtain homogeneity and consistency.

4. Determine that a 25kilo sack of "GLORIA LEIMPLAST" needs 5-6 liters of water. You have at your disposal 2-3 hours to use the quantity preparation. The time calculated at normal ambient temperature (23 ° C and 50% relative humidity)

5. Apply with a trowel until two plies 3-4 mm thick

6. smooth surface needs a hand of "lath" from the same material

7. In line with forearm easily without getting up

When it start tightening surface, to 'draw', smooth with hard sponge float or Styrofoam since wet.

Each screed drying time ranges from one half to two hours, depending on temperature, relative humidity, wind, porosity and coating thickness.

If the application is done to a greater or lesser thickness than the recommended does not "sag" or detached from the background.

Consumption

Required 8 to 10 kgs of material to coat a square meter of 3-4 mm thickness.

RAPID-SETTING RECONSTRUCTION PLASTER

Industrial product used for coating building surfaces (old plaster, brick, concrete, ceilings).

Replaces traditional plasters "roughcasted and marble."

Applied in the same way in two or three layers of 5-6 millimeters each.

The same material is used as a "scratch".

PRODUCED AS WHITE AND COLOURED

ADVANTAGES

Stable composition and mixture homogeneity

Very good workability

Strong adhesion without lime

No cracks or capillaries at high temperatures

Applied by hand or with a press

Has high resistance to frost (resistance to delamination - adhesion loss)

Manual

1. Clean dust from loose areas or oils formwork surface.

2. Dampen with water if it comes to absorbing surface or high temperature (over 30 degrees)

3. Combine material from the package to the appropriate amount of water to vessels or mixer until the slurry prepared obtain homogeneity and consistency.

4. Determine that a 25kilo sack of "GLORIA MASTERPLAST" needs 5-6 liters of water. You have at your disposal 1 hour to use the quantity prepared before it starts to tighten and thicken. The time is calculated based on normal ambient temperature (23 ° C and 50% relative humidity)

5. Apply with a trowel until two players thick 5-6 millimeters

6. Smooth surfaces need a layer of "lath" from the same material

7. If it is applied to a greater thickness than the recommended, the product does not "sag" or getting detached from the background and is easily aligned afterwards.

8. When you start tightening surface to 'draw', smooth with float, hard sponge or styrofoam, after you put some water on them.

9. Each screed drying time ranges from one half to two hours, depending on temperature, relative humidity, wind, the absorbency of the substrate and the coating thickness.

10. In column associations or spar with bricks or other dissimilar surfaces use a reinforcing mesh plaster.

Consumption

They take 10 to 12 kgs of material to coat a square meter of 5-6 mm thickness.

ACRYLIC TILE ADHESIVE

New synthesis product based on white cement and synthetic resins, ideal for bonding all kinds of ceramic tiles on cement floors and plastered walls (such as bathrooms etc.). Professional product, shows excellent workability, adhesion, moisture resistance and early mechanical strength. If strengthened improver emulsion «GLORIA DMG» is also used for pasting new tiles onto old or worn tiles, is prefered. The «GLORIA ROYAL» is a product that guarantees perfect placement in any medium. Classified C2T in accordance to European standard EN 12004.

INSTALLATION PROCEDURE:

· All the walls and floor supports are suitable for use as long they are, flat, compact, durable and purified.

· Stir quantity of «GLORIA ROYAL» with clean water in basin or bucket and homogenize with an electric mixer to a paste created not showing lumps or insolubles. The mixing time is usually 3-4 minutes. Each 25kilo sack requires 6-6,5 lt. water. Inside the container the mixture preparation stays plastic and obtainable for 4-5 hours at normal room temperature. Periodically you need to agitate the slurry sometimes as not to create surface film (skin).

Technical data

· Bagged PRODUCT

APPEARANCE: Whitish premixed MORTAR

Density: 1.5gr / ml

SOLID INGREDIENTS: 100%

TIME CONSERVATION - STORAGE: 12 months in original sealed containers and in a place suitable, low humidity.

DEGREE OF RISK: MINIMUM (CEE88 / 379)

RATE OF MIXING WATER: 24 to 26 wt%.

RETENTION TIME IN THE CONTAINER: ABOUT 5 HOURS

AVAILABLE TIME OF APPLICATION: 20 MINUTES (EN1346)

CORRECTION TIME: 20 MINUTES (DIN 18156-2)

RESISTANCE TO SLIPPING: <0.5 (EN 1308)

pulp pH: ~ 12

STEPPING FLOOR: AFTER 24 HOURS

ABILITY TO WALL JOINTING: after 3-6 hours

JOINTING ABILITY TO FLOOR: AFTER 24 hours

CONSUMPTION:

 3-5 kg per square meter, or depending on the size of the plates and positioning thickness. Old mosaics raise this figure to 8-10 pounds since it needs leveling of interchanged corners (edges).

'GLORIA' SUPER

PROPERTIES

Special tile adhesive Super Acrylic is formulated with perfect applications for extreme resistance to compression and posting. Suitable for all types of tiles of large or small dimensions. For skirting welding, brick, stone, granite, Klinker and Cotto, for exterior and interior. Meets fully the requirements of C2TE S1 class.

ADVANTAGES

 Very strong glue for special welds with excellent results in mosaic, tesserae, Porobeton, plasterboard, for commercial and industrial traffic areas.

Resistant to vibration and pressure. Highly resistant to temperature variations. A constant composition and homogeneity with good adhesion and good workability.

Manual

Combine the adhesive with water in a clean container.

Ratio 25 Kg of powder to 6.7 liters of water, until a paste with no lumps (recommended mechanical stirring) is formed.

Allow the mixture to homogenize for 5 minutes and then stir periodically without adding water. The adhesive remains workable for 4-5 hours.

Consumption

Required 4-5 Kg / m² depending on the surface and the size of the tiles.

Specifications

white mortar

coagulation Pot (Pot-life) 4-5 hours

Available application time 30-40 minutes

Minor adjustments and corrections Time 50 minutes

Grouting after 24 hours for floors, after 12 hours for wall

Installation temperature from + 5ºC up to + 35ºC

Temperature resistance from -30ºC to + 120ºC

Specific weight 1,4 Kg / lt

Foot traffic 24 hours

Resistance aging Excellent

Resistance to oils, solvents Excellent